The Gyro G3 upper top plate is designed for use with the G3 detangler.
Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
Unique design with Thermalite for durability. In-moldED Steel insert to eliminate bar punch through. Expands securely with a grub screw to fit tightly on regular, 9, 11, & 13 butt bars. - Expands securely with a grub screw to fit tight - Material: Thermalite - Weight: 1.0-ounces per pair
- Sold in pairs. - Allen wrench included.
The Graduate sleeve is the replacement sleeve for the Graduate peg that's made from long lasting, fast sliding plastic. - Sold singly
The M2 lever works with a single cable or Odyssey's dual cable system. - Improved braking power for Gyro users - Left/Right hand compatible
- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)
The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.
The MK 4 version continues the GLAND’s heritage, but in a smaller and sleeker overall size which should appease many riders. The images beside show the top, profile, and under side of each guard.
Broc Raiford can bunnyhop over a house so it’s only right that he has his own grips to hold on to. Broc’s signature grip comes in at 160mm in length and features rope detailing on the ends to tie in with Broc’s nautical theme.
$9.99 - $22.99
- Press fit designed to work the hub's non-drive side collar.
- New ultra-slim 2014-T6 aluminum seat clamp with replaceable hardware and self-aligning nut. - 6061-T6 aluminum construction. - Standard 1-1/8-inch size.
$9.99 - $11.00
Sunday's Cornerstone Grips rock traditional styling, current branding, and come in at 150mm in length with plenty of color options. It's not a bad idea to keep an extra pair around.
The product designers at Sunday worked closely with Jake to nail down a grip that is perfect for him. Jake's grip comes in at 160mm and features a gradually increasing rib width. This grip can be run either way, depending on which side you prefer. The grip also features a tapered core for comfort.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield lever is easy to install and remove without having to wrestle grips on and off. An ordinary hinged clamp can be bulky and expensive so a new clamping design made specifically for die-casting was used. This approach keeps the lever reliable and affordable. The lever handle is the same comfortable shape as the proven Monolever Medium blade.
- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Upper - Length: 11 - 12.5" - Diameter: 1.5mm
This is Odyssey's top-of-the-line brake cable that ties together all of their most advanced braking technology. - Utilizes the original BMX Linear Slic Kable housing to prevent binding when the bars are rotated. - Factory installed ferrule ends with inner volcano shape to prevent housing blow out; a Linear Slic Kable standard since 2008. - Specially coated inner wire for ultra low friction, a proven feature resurrected from their once famous Brakeline cables. - Gyro lug included at one end of the inner wire for use with detanglers. - 60-65mm in length. - Black
The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing (2.9 oz). - Black - 60 – 65mm
- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Lower - Length: Dual Cable - Diameter: 1.5mm
- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Upper - Length: 7.5 – 9.5-inch - Diameter: 1.5mm
- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Lower - Length: X-Long - Diameter: 1.5mm
$13.99 - $21.99
One of the most successful and popular pedals, and for good reason with its extremely simple, lightweight, inexpensive and famously durable plastic-bodied design. Often duplicated but never replicated. - High-strength plastic composite
The new Gsport Uniguard is a simple, inexpensive functional guard that eliminates the need to spread the dropouts. It’s made from Heat-Treated Cr-Mo Steel and is LHD and RHD compatible as well as Drive and Non-Drive compatible. All bases covered. Available in 14mm or 3/8?.
For the Bluebird chain, Odyssey took the proven and reliable KMC 510-HX chain and added a permanently attached, factory installed half-link to one end. When the chain is trimmed to size you can easily decide whether or not to use the half-link. Original factory assembled pin joints are radically stronger than workshop assembled ones, so this is a huge benefit.
- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)
Odyssey took their proven Linear Slic Kable housing and replaced the steel linear wire with aluminum. Utilizing the aluminum wire in the housing saves you significant weight, roughly 30%. This cable also features their specially designed “volcano” ferrules that they’ve used since 2008 to prevent housing blowouts. This Kable also comes with color-coaded inner wires and ball ends to differentiate between their regular Linear’s Race Linear Slic Kable. - Length: 60 – 65mm - Black
As the name implies, this new version can be easily adjusted to cover 3 different lengths by utilizing the cable’s unique straddle interface connection. This tool-free feature allows the Adjustable Quik Slic Kable to be a one-size-fits-all cable for virtually every braking configuration. FEATURES - Adjustable hanger slot allows upper cable to rotate for optimum alignment. - The integrated hanger and straddle cable creates direct routing to brake arms with no bends or twists to reduce flex. - Linear K-Shield mesh housing offers higher compression rate and lighter weight than standard steel mesh. - All Odyssey Linear cables are offered with the K-Shield housing. - Specially designed and machined Volcano ferrules prevent premature housing blowout. Velcro strap included. SPECS - Housing length: 995mm - Frame requirements: Slotted cable stop and guides. 245mm (+/-3) distance from center brake boss to the front of the cable stop is recommended. - Brake requirements: Open-ended U-brake arms. - Works with most brake levers. - Velcro strap included.
The Silencer V2 has a lightweight 6061 aluminum core supports the entire sleeve. The sleeve is made from our proprietary Thermalite material and resists cracking and deformation while sliding better than chromoly on most surfaces. The lengthy 4.4" peg ensures you maintain locked into grinds. - Axle: 3/8" with included 10mm adapter - Diameter: 1.6" - Length: 4.4" - Weight: 5.3-ounce each - Sold individually
- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Lower - Length: Fits most - Diameter: 1.5mm
- Precise fit and smooth function - Great cable travel range - Shielded cables for durability - Includes upper and lower cables - Use: 1-1/8" BMX
Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro since 1986 and constantly improving it along the way. Everything you need to run a Gyro. Odyssey Gyro cables and upper and lower cable stops included.
$19.99 - $26.99
- Straight gauge spokes with a proprietary grade of stainless steel that is as good or better than the materials used by the world’s most renowned spoke makers. - Sized and dimensioned specifically for BMX.
This custom 7075-T6 aluminum pre-load bolt design is included with every Odyssey fork. - Fits both a 6mm and 8mm allen key. - Front brake cable thru-way hole for removal without disconnecting brake hardware. - Designed with an easy-cut thread groove if you cut your fork’s steerer tube down.
- Threads onto 3/8" axles - Double-sided - Oversized - Alloy - Length: 3" / 74mm - Width: .94" / 24mm - Sold as a pair
- CNC machined 6061-T6 aluminum chain tensioners - Compatible with 3/8 inch and 10mm axles - Single bolt operation makes tensioning a simple task - Material: 6061AL
- Steel - Threads onto 3/8" axle - Knurled & grooved - Diameter: 33mm - Sold in pairs
Protect your bars and prevent your grips from getting shredded with WeThePeople's Supreme Bar Ends. CNC machined from 6061 aluminum, these tough, bolt-in end caps protect your investment from tons of abuse when you have to jump ship on an imperfect execution of a trick. Simply slide them into the ends of your handlebars and tighten them up. Then, go nuts!
- Super hardened nylon construction - 40mm diameter, 100mm length - Special insert fits 3/8" or 14mm axles - 90g (pair)
Designed specifically for use with Odyssey's Quartet FRONT or REAR hubs. SPECS - Forged from 7075-T6 aluminum for greater strength and durability - Steel insert prevents guard deformation, prolonging bearing life
A classic knobby version of the Aitken signature tire. Traditionally a more dirt-specific tire but the tire’s fast rolling center tread allows it to be used on all terrains. - 20 × 2.35 only Single ply casing
Mike Aitken's popular signature tires for street and dirt. Ideal for use at high speeds. - 20 × 2.25, and 20 x 2.45 Dual ply casing
Tom likes to ride fast and go very high. These tires were designed to help him do just that. With a fast center tread, these tires are made for park, street and even dirt too. The side profile is reminiscent of a motorcycle tire as well, which is a nod to Tom’s motorcycle lovin’ ways.
Odyssey is proud to offer their new tripod post. It allows for the two most popular seat angles amongst riders and it’s clean, light and easy to install. SPECS - 25.4mm diameter - 6061-T6 Aluminium, CNC machined
Designed using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 10mm, 3mm and 2mm (15mm total) - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1-1/8 integrated headset. - 45º tapered bearings 41.8mm outer diameter (fits 42mm BMX head tubes).
New dust cap design, with Monogram laser etched logo, for a cleaner look to accommodate a taller riding set up with less spacers. Same quality as Odyssey's Pro Headset using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 15mm dust cap. With 3mm, and 2mm spacers - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1 1/8-inch integrated headset. - 45º tapered bearings - 41.8mm outer diameter (fits 42mm BMX head tubes).
- Allows the use of wheels with 3/8" axles to be used with frames or pegs requiring 14mm axles - Durable chromoly construction - Sold in pairs
8 spline BMX bottom bracket Spindle with bolts. - Diameter: 19mm - Crank arm Interface: 8-spline - Length: 150mm - Bolts included
- 4130 chromoly axle pegs with 3 position anti-rotation set screw - Designed for use with 14mm or 3/8" axles (with adapter) - 4130 chromoly offers a durable, long lasting peg with a smooth grind - 3 set screw positions extend the life the of the peg - Axle: 14mm / 3/8" - Diameter: 35mm - Material: Chromoly - Sold in pairs
It’s a traditional straight up pivotal design with a 200mm length.
- Forged alloy construction - Double bolt centering design - Oversize 6mm hex bolts
WeThePeople's Feelin tire has a slick-tread design with a durable, grippy rubber compound, making it an awesome choice for the street and park.
Odyssey racing spokes use butting dimensions that are tailor-made for BMX racing, and they’re still strong enough to handle some light street riding too. You’ll save roughly an ounce per wheel on 36’s. Only the best stainless steel has been used, and the gradual butting transitions are ideal for the stresses that a 20-inch wheel has to endure. - Proprietary professional-grade stainless steel. - BMX specific butting transition dimensions.
A huge leap forward in pedal technology that results in a simpler overall design. Extremely lightweight plastic bodies eliminate the need for bearings and allow for a spindle that is significantly stronger than normal. Metal pins make the pedal very grippy, and the pedal will still function normally when pins are removed from one side for grind tricks. No flimsy outboard end caps. Pedal body halves are easy and inexpensive to replace – instead of replacing the whole pedal. - 9/16-inch, heat-treated, 4140 chromoly spindle - Proprietary high-strength plastic composite
Shimano's DXR V-Brake Levers are the choice of the pros, from the Olympics to the local race scene. They use a 2-finger design with Shimano's proven Super Linear Response system that gives you great power and feel with little effort.
6061 aluminum with precision sealed mechanism bearing and lower (17mm) stack height.
WeThePeople's Socket Pivotal seat post is made from 6061 aluminum for a perfect blend of strength and weight savings. It works with all Pivotal seats and comes in the perfect color and size to match your bike. Plus, there's a 17mm socket head built into the bottom of the post for park-side adjustments to your wheels.
- Super hardened Cr-Mo/Nylon construction - 40 x 100mm - Special insert fits 3/8" or 14mm axles - Diameter: 40mm - 320g (pair) - Material: Chromoly Core w/Nylon Sleeve - Sold in pairs
Page 1 of 2 Next page